Up next 1955 International Harvester UD-18A Published on September 06, 2022 Author Mike McGlothlin Share article Facebook 0 Twitter 0 Mail 0 De-Stroked Duramax at a insane 7,800 High-RPM The Inner Workings of An LMM Built to Live at High-RPM We see a lot of engines go together here at Diesel World, but occasionally we’re able to sit in on a high-horsepower build that breaks the mold. After playing a key role in keeping as many as seven pulling trucks operational during the summer, Kevin Dermody of Dermody Diesel didn’t settle in for a long winter’s nap once the weather in his native Illinois turned cold. Instead, he found himself busy indoors, piecing together a fairly unique combination of parts for a power-hungry Duramax owner. It wouldn’t be a big bore engine nor a stroker, but rather a de-stroked LMM designed to live at high rpm. At the heart of the build, you’ll find a Callies Ultra Billet crankshaft with a custom, 3.750-inch stroke (vs. 3.897-inch stock) that was internally balanced at Wagler Competition Products. Callies machines the crank from triple heat-treated 4330v steel before being treated to the company’s Perma-Case nitriding process (for surface hardening). Compared with the factory forged steel crankshaft from GM, the rod journals are narrower (2.165 inches in width) for improved strength. Designed and intended to be run upstairs, the short-stroke engine is void of a girdle or billet main caps, but does employ ARP main studs. Made from 8740 Chromoly steel, ARP’s main studs have a 200,000-psi tensile strength rating. Prior to the engine’s assembly, the entire rotating assembly (complete with an SFI-approved Fluidampr harmonic balancer and Sun Coast Performance zero balance flex plate) was internally balanced at Wagler Competition Products. All of the machining (including line boring of the main bearing bores) took place at Wagler’s Odon, Indiana facility as well. Having been around big bore and stroker versions of the 6.6L in the past, Dermody was accustomed to sizing turbochargers for stock or increased displacement engines. Needless to say, turbo selection presented a new challenge for a high-rpm screamer. First and foremost, he wanted chargers that wouldn’t run out of steam at 3,500 rpm. However, he needed them to be reasonably responsive at low rpm. Beyond turbo selection, Dermody would enlist the help of some of the biggest names in the industry, with companies like Wagler Competition Products, Diesel Technology Source, S&S Diesel Motorsport, and HSP Diesel all coming onboard. For a look at the complete build sheet behind this short-stroke, 390 ci Duramax’s somewhat unorthodox route to making power, keep reading.Subscribe Our Weekly Newsletter The Ultra Billet crank swings a set of forged-steel connecting rods from Wagler, which accommodate a Trend Performance Hemi-style wrist pin on the small end. Forged from 4340, the I-beam style rods are shot-peened for enhanced strength and utilize 7/16-inch ARP2000 cap bolts. Used in countless truck pulling and drag racing applications, these rods have been proven to handle more than 2,000 hp without issue. A forged aluminum, 16:1 compression Ross Racing piston resides in each cylinder. The 4.075-inch bore (vs. 4.055 stock) pistons feature Ross’s black skirt coating, much like hard-anodizing, with a Teflon seal for longer skirt life. To safeguard against piston-to-valve contact at high rpm, 0.095-inch deep valve reliefs are present. Valve actuation is controlled via a Dominator series, standard firing order camshaft from Diesel Technology Source. Wagler 4130 Chromoly, 3/8 x 0.135-inch wall pushrods link the cam to the billet rocker shafts (also sourced from Wagler). With big horsepower comes the need for added oil pressure, and one of Wagler’s pinned oil pumps got the call for this build. The pump’s 0.030-inch shims provide for 25 psi of oil pressure at idle and 90 psi peak. For added peace of mind, the oil pump is pinned to ensure the gear never spins on the shaft. For optimum combustion sealing, the block was machined to accept stainless steel O-rings. Wave-Stopper head gaskets from Mahle, feature a patented design that entails concentric waves around the combustion chamber area to allow each gasket to adapt to varying loads and pressures, and accommodate the 0.064-inch thick O-rings. A set of Dominator series race heads from Diesel Technology Source were supplied for the build and anchored to the block by way of ARP Custom Age 625+ head studs. The stock size intake and exhaust valves were retained (33mm and 31mm, respectively), but the heads underwent extensive CNC porting. As a result, the intake valves flow 225 cfm per cylinder (stock heads max out at roughly 180 cfm). Dual valve springs with Titanium retainers provide the proper spring rate and seat pressure for the kind of elevated rpm and boost levels the engine will see. Also notice the Dirty Hooker Diesel billet-aluminum coolant block-off plate behind the passenger side head, which was installed to rule out the possibility of the common coolant leak occurring at the rear engine cover. Topping off the heads, Dermody installed a set of these trick upper valve covers from Wagler. They’re machined from billet 6061 aluminum, feature a leak-free O-ring seal, and come with all 28 required mounting bolts. With the water pump being a common failure point in Duramax mills that see excessive engine speed—and because this engine will often find itself above 4,000 rpm—a welded or pinned factory water pump just wouldn’t suffice. For ultimate peace of mind, a Wagler billet water pump got the nod. It employs a billet impeller (vs. plastic on late-model Duramax’s), a hardened tool steel shaft, ceramic seals, roller bearings, and an anodized hard coat. To avoid overspeeding issues that might surface while running a VGT at high rpm, two fixed geometry turbos are used in the engine’s compound arrangement. Sourced from HSP Diesel, the T4 pedestal for the high-pressure charger utilizes the factory turbo mounting points at the back of the lifter valley. The exhaust gases used to drive the high-pressure turbo route through PPE Power high-flow, cast-iron manifolds, and 2-inch diameter stainless steel up-pipes, both of which are heat-wrapped to aid spool up. Rather than opt for dual CP3’s, Dermody replaced the factory unit with a 14mm stroker pump from S&S Diesel Motorsport. With 71 percent more displacement than a factory CP3, this LBZ-based unit is known to support more than 1,500 hp (at the crank), and also eliminates the 3,000-plus rpm fuel flow restrictions present in stock CP3’s. The reason behind the 14mm CP3 becomes clear when you realize it has eight 250-percent over injectors to feed. Also built by S&S Diesel Motorsport, the 250-percent over units are capable of supporting between 1,000 and 1,700 hp (at the crank), depending on how much air you have available. A set of Industrial Injection’s billet-steel injector hold-downs (with ARP mounting bolts) fasten the S&S injectors in place in the heads. A high-rpm engine presents a unique challenge in turbo selection. First things first, you want turbos that aren’t out of steam at 3,500 rpm. However, you also need them to be as responsive as possible at low rpm. To perform well in both extremes and last while doing it, Dermody turned to the proven S300 and S400 platforms available from BorgWarner. Starting with a box S366 SX-E (the unit shown), the turbo was treated to compressor wheel, turbine wheel, and map groove work, which culminated in a 15-percent gain in flow. The T4 charger retains its 360-degree thrust bearing assembly for optimum shaft support and makes use of a 73mm (exducer turbo) turbine wheel inside a 0.91 A/R exhaust housing. With the long block assembled and the CP3, injectors, and turbo pedestal installed, an oil pan from PPE was bolted on, too. The cast-aluminum pan is designed to drain completely but also adds an extra quart to the engine’s oil capacity. Picked to serve as the atmosphere turbo, an S480 SX-E-based charger sits next to the passenger side battery. It too benefits from the compressor and map groove enhancements, as well as flowing approximately 15 percent more air than it did in stock form (135 lbs/min or roughly 1,930 cfm, stock). The big T6 turbo conceals an 88/96mm turbine wheel inside a 1.32 A/R exhaust housing. To keep both the free-flowing S480 SX-E as responsive as possible while also reducing radiant heat under the hood, a DEI turbo blanket is employed, along with an exhaust wrap around the HSP Diesel hot pipe. The Max-Flow Y-bridge, 3-inch hot-side, and 3-inch cold-side intercooler pipes were also sourced from HSP. The S400 routes exhaust out a 4-inch downpipe. Back in the truck, the freshly-built LMM rests on XD motor mounts from the Dmax Store. An LML-derived upper radiator hose, Mishimoto intercooler, DTS-built Allison six-speed, BD Diesel Double-Stack transmission cooler, 260-gph FASS Fuel System, and RCD Performance sump would also be installed before all was said and done. For Dermody, the last order of business before handing the keys over to the truck’s owner entailed 100 break-in miles and a trip to the chassis dyno. Aboard the rollers, a little EFI Live magic from the tuning gurus at Custom Tuning Team will be used to get the truck as far into four-digit horsepower territory as possible. As an extreme example of what a de-stroked Duramax is capable of, look no further than Tony Rizzi’s Outcast. The Nitrous Express -huffing short-stroke in his ’37 Chevy pickup spins an insane 7,800 rpm, has carried him through the eighth mile in as little as 4.5 seconds, and has been as fast as 171 mph. Factoring in the truck’s trap speed with its race weight, more than 2,000 hp is making it to the rear wheels. SOURCES ARP 800.826.3045 arp-bolts.com Callies Performance Products 419.435.2711 callies.com Dermody Diesel 217.473.4606 dermodydiesel.com Diesel Technology Source 770.266.0555 dieseltechnologysource.com Dmax Store 877.469.3629 dmaxstore.com Fluidampr 716.592.1000 fluidampr.com HSP Diesel 586.785.3110 hspdiesel.com Industrial Injection 800.836.4207 industrialinjection.com Mahle us.mahle.com PPE Power 714.985.4825 ppediesel.com RCD Performance 309.822.0660 rcdperformance.com Ross Racing Pistons 800.392.7677 rosspistons.com S&S Diesel Motorsport ssdiesel.com Sun Coast Converters 800.868.0053 suncoastdiesel.com Wagler Competition Products 812.636.0391 waglercompetition.com Total 0 Shares Share 0 Tweet 0 Pin it 0 Share 0
Mix & Match Robbie Watson spent two years collecting parts to fabricate his personal best. Robbie Watson owns his own wrecker service in Branchland, WV and has been […] JOE GREEVES April 02, 2021 Chevy Diesel Trucks Dodge
The Evolution of Cummins Killer From Homegrown, Pro Stock Duramax To Triple-Turbo, Mechanical Monster It’s been on the scene since 2008, in one form or another. From Pro Stock to […] Mike McGlothlin July 19, 2021 Chevy Diesel Trucks GM
5 POWER-HUNGRY CLASSIC CHEVY TRUCKS Kicking Ass With Some Class! These diesel Chevy trucks have quite a few years under their belt, however, they’re still performing as if they’re right […] Adam Blattenberg September 04, 2020 Chevy Diesel Trucks
900 HP Duramax Daily Daily Driver-Turned 900HP Work Stock Puller Just as in any other industry, being in-the-know in your specific corner of the automotive world can land you […] Mike McGlothlin March 06, 2020 Chevy Diesel Trucks GM
![](https://ad.ipredictive.com/d/track/event?upid=111299&url="https://www.dieselworldmag.com"&cache_buster=1734532055&ps=1)